KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
- 8. Transmission
   + 8.1. Mechanical transmission
   - 8.2. Automatic transmission of F4E-K
      8.2.1. Specifications
      8.2.2. Check of work and adjustment of position of the lever of the selector
      8.2.3. Testing of collaboration of an automatic transmission and the engine on the motionless car (stall test)
      8.2.4. Testing of a time lag (Lag test)
      8.2.5. Check of pressure of transmission liquid
      8.2.6. Check of level and liquid replacement in an automatic transmission
      8.2.7. Procedure of replacement of liquid in the converter of an automatic transmission
      8.2.8. Leakages of liquid from an automatic transmission
      8.2.9. Replacement of oil sealing rings
      8.2.10. Removal and installation of an automatic transmission
      8.2.11. Repair of an automatic transmission
      8.2.12. Radiator of cooling of liquid of an automatic transmission
      8.2.13. Block of valves
      8.2.14. The case of regulating valves
      8.2.15. Oil pump
      8.2.16. Check of resistance of the sensor of frequency of rotation of an entrance shaft \turbine wheel
      8.2.17. Check of resistance of the sensor of speed
      8.2.18. Switch of operating modes of a transmission of O\D
      8.2.19. Switch of a range of a transmission
      8.2.20. Sensor of temperature of an automatic transmission
      8.2.21. Electromagnetic valves
      8.2.22. Linear electromagnetic valve
      8.2.23. Selector lever
      8.2.24. Repair of the lever of the selector
      8.2.25. Check of functioning of the mechanism of blocking of the lever of the selector
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Air central air
+ 16. Electric equipment


8.2.23. Selector lever

GENERAL INFORMATION

Selector lever

1–central panel;
2–ashtray;
3–forward section of the central console;
4–central console;
5–selector lever;
6–arm;
7–lighter socket;
8–selector cable;
9–selector cable;
10-adjusting plate;
11-socket.

Removal

PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.
2. Remove an ashtray and turn out two screws.
3. Disconnect the socket of the lighter and remove the central panel.
4. Remove forward section of the central console and the central console.
5. Move the selector lever to a position P.
6. Turn out two bolts of fastening of a cover of a cable of the selector.
7. Turn out nuts of fastening of a cable of the selector.
8. Turn out nuts of fastening of a cable of blocking and disconnect it from the blocking lock.
9. Remove an arm.

10. Disconnect the socket of the switch of operating modes of O/D.

11. Turn out nuts of fastening of a basic plate of the selector and remove the selector lever assembled.

Installation

PERFORMANCE ORDER
1. Establish the lever of the selector and fix a basic plate of the selector nuts.

Inhaling moment: 15,7–22,6 N • m


Prevention

At installation of a basic plate of the selector of the shooter on a plate it should be directed to a forward part of the car.


2. Establish an arm.
3. Connect the socket of the switch of operating modes of O/D.
4. Move the selector lever to a position P.

5. Tighten nuts of fastening of a basic plate of the lever of the selector.

Inhaling moment: 6,8–9,8 N • m

6. Tighten a bolt of fastening of a cable of the selector and a nut.

Inhaling moment: 6,8–9,8 N • m

7. Tighten nuts of fastening of a cable of blocking.

Inhaling moment: 9,8–14,7 N • m

8. Establish forward section of the central console and the central console.
9. Establish the central panel and connect the socket of illumination of the lighter.
10. Establish an ashtray.
11. Connect a wire to the negative plug of the storage battery.
12. Check correctness of operation of the lever of the selector.