KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Air central air
- 16. Electric equipment
   16.1. Specifications
   16.2. Electric chains
   + 16.3. Generator
   + 16.4. Storage battery
   16.5. Starter
   16.6. Check at a provorachivaniye of a cranked shaft not the heated-up engine
   16.7. Check of an electric chain of the traction relay
   16.8. Check of the traction relay
   16.9. Check of brushes and shchetkoderzhatel
   16.10. Check of coils of a stator
   16.11. Rotor check
   16.12. Removal and starter installation
   16.13. Starter repair
   16.14. Multipurpose switch
   16.15. Sound signal
   16.16. The block of safety locks and the relay, established in car salon
   16.17. Check of the relay of the activator of the lock of a door
   16.18. Check of the switch of adjustment of provision of an external rear-view mirror
   16.19. Check of the activator of provision of an external rear-view mirror
   16.20. Check of the engine of a window regulator
   16.21. Check of a heater of back glass
   16.22. Repair of a current-carrying strip of a heater
   16.23. Engine of a screen wiper of a windscreen
   16.24. Stekloomyvateli
   16.25. Adjustment of light of headlights
   16.26. Adjustment of light of fog lights
   16.27. Safety cushions (SRS)
   16.28. Precautionary labels
   16.29. Safety cushion of the driver and spiral wire
   16.30. Safety cushion check
   16.31. Check of a spiral wire (spring)
   16.32. Safety cushion of the forward passenger
   + 16.33. Electric circuits


16.23. Engine of a screen wiper of a windscreen

GENERAL INFORMATION

Screen wipers of wind and back glasses

1–cowl lattice;
2–lever of a screen wiper of a windscreen;
3–engine of a screen wiper of a windscreen;
4–drafts of a screen wiper of a windscreen;
5–lever of a screen wiper of back glass;
6–engine of a screen wiper of back glass.

Check of frequency of work of a screen wiper

PERFORMANCE ORDER
1. Disconnect the socket from the screen wiper engine.
2. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 1.
3. Be convinced that the engine of a screen wiper works at low frequency of rotation.
4. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 2.
5. Be convinced that the engine of a screen wiper works at high frequency of rotation.

Check of an automatic stop of brushes in an initial condition

PERFORMANCE ORDER
1. Turn on the engine on low frequency of rotation.
2. Having disconnected a wire from contact of 1 socket, stop the engine in any situation, except the initial.
3. Connect contacts 1 and the 5th socket.
4. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 3.
5. Check that the engine of a screen wiper is switched off in a starting position of brushes of a screen wiper.

Adjustment

PERFORMANCE ORDER
1. Establish screen wiper levers on an axis in a starting position.
2. Screw nuts of fastening of levers and tighten them the demanded moment.

Inhaling moment: 18–22 N • m

3. Establish covers on nuts and check work of a screen wiper of a windscreen. Brushes of a screen wiper should stop in a starting position at distance of 41 mm from the forward passenger and – 40 mm from the driver.