KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
- 1.1. Short acquaintance to the car
   1.2. Keys
   1.3. Locks of doors
   1.4. Immobilizer
   1.5. Electric window regulators
   1.6. Seats
   1.7. Seat belts
   1.8. Back seat belts
   1.9. Safety cushions
   1.10. Components of system of safety cushions
   1.11. Control lamp of a safety cushion
   1.12. Luggage carrier door (5-door model)
   1.13. Trunk lid
   1.14. Lamp of a luggage compartment
   1.15. Cowl
   1.16. Hatch of a fuel tank
   1.17. Steering wheel
   1.18. Rear-view mirrors
   1.19. Illumination of salon
   1.20. Salon equipment
   1.21. Digital watch
   1.22. Shtorka of a luggage carrier
   1.23. Power supply socket
   1.24. Aerial
   1.25. The hatch in a roof
   1.26. The holder for sunglasses
   1.27. Cargo luggage grid
   1.28. Top luggage carrier
   1.29. Ignition switch
   1.30. Engine start-up
   1.31. Mechanical transmission
   1.32. Automatic transmission
   1.33. Brake system
   1.34. Parking brake
   1.35. Hydraulic amplifier of a steering
   1.36. Adjustable steering column
   1.37. Combination of devices
   1.38. Headlights
   1.39. Turn indexes
   1.40. Proof-reader of light of headlights
   1.41. Illumination of a day mode of operation
   1.42. Back antifog lamps
   1.43. Screen wipers and stekloomyvatel
   1.44. Heater of back glass
   1.45. Heater of an external rear-view mirror
   1.46. Heating and ventilation system
   1.47. System work
   1.48. Information on plates
   1.49. Alarm light system
   1.50. Engine start-up from the storage battery of other car
   1.51. Safety locks
   1.52. Memory safety lock
   1.53. Car towage
   1.54. Screen wiper brushes
   1.55. Replacement of lamps
   1.56. Care of appearance of the car
   1.57. Maintenance
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Air central air
+ 16. Electric equipment


1.55. Replacement of lamps

GENERAL INFORMATION

REPLACEMENT OF THE LAMP OF THE HEADLIGHT (FOUR-DOOR MODELS)


Prevention

At replacement of a lamp protect eyes. Wait, that the lamp cooled down, but only then replace it.

Halogen lamps are filled with gas under pressure. In a case a razbitiya the halogen lamp will blow up and its splinters will scatter in different directions.

Always handle with care with a halogen lamp and avoid рисок and scratches. If lamps burn, prevent their contact to liquids. Never concern some glass barehanded. The remains of fat can cause an overheat and lead to lamp explosion if it burns. The lamp can be included only after its installation.


PERFORMANCE ORDER
1. Open a cowl.
2. Disconnect the electric socket from a lamp, having pressed the socket from two parties.
3. Release a wire spring of fastening of a lamp of a headlight, having pressed its end and having pulled up.
4. Take a lamp from three grooves on a headlight.
5. Establish a new lamp in three grooves on a headlight and latch a wire spring of fastening of a lamp in the provision of fixing.
6. Connect the electric socket of a lamp of a headlight.

REPLACEMENT OF THE LAMP OF THE FORWARD INDEX OF TURN / LAY FIRES

PERFORMANCE ORDER
1. Turn a cartridge of a lamp of lay fires counter-clockwise take it from the headlight block.
2. Take a lamp from the boss, having pulled for it.
3. Establish a new lamp in a cartridge.
4. Establish a cartridge of a lamp of lay fires in the block of a headlight and turn it clockwise for blocking of the boss on a place.

REPLACEMENT OF THE LAMP OF THE BACK INDEX OF TURN

PERFORMANCE ORDER
1. By means of a crosswise screw-driver turn out screws of fastening of the back combined lamp to a body.
2. Carefully remove lamp knot from the car.
3. Turn a cartridge of a lamp counter-clockwise and take it from the case.
4. Press a lamp and turn it on a turn quarter counter-clockwise then take a lamp from the boss.
5. Insert a new lamp into a cartridge then press a lamp and turn it on a turn quarter clockwise to fix a lamp on a place.
6. Establish a cartridge of a lamp in the back combined lamp and turn it on a turn quarter clockwise for blocking of the boss on a place.
7. Carefully establish lamp knot on the car.

REPLACEMENT OF THE LAMP OF THE CEILING PLAFOND

PERFORMANCE ORDER
1. Using a flat screw-driver, carefully remove glasses from the case of a ceiling plafond.
2. Press a lamp inside, then turn it on one quarter of a turn counter-clockwise and take out a lamp from the boss.
3. Insert a new lamp into a cartridge, further slightly press a lamp inside and turn it on a turn quarter clockwise so that the lamp was established into place.
4. Put two glasses to the case of a ceiling plafond according to cuts and latch glasses on the places.

REPLACEMENT OF THE LAMP OF THE LAMP OF ILLUMINATION OF REGISTRATION PLATE

PERFORMANCE ORDER
1. Using a screw-driver for Phillips bolts, unscrew two bolts serving for fastening of glass, and remove glasses.
2. Carefully take out a lamp from the boss.
3. Insert a new lamp into a cartridge.
4. Establish back glasses and fix them two bolts.