KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
- 9. Axes and power shafts
   9.1. Specifications
   9.2. Check of a condition of a protective cover
   9.3. Check of reliability of shlitsevy connection
   9.4. Replacement of a power shaft
   9.5. Repair of a power shaft
   - 9.6. Forward axis
      9.6.1. Check люфта bearings of forward wheels
      9.6.2. Rotary fist and nave of a forward wheel
      9.6.3. Bearing of a nave of a forward wheel
      9.6.4. Adjustment of a tightness of bearings of a nave of a forward wheel
   9.7. Back axis
   9.8. Adjustment of a tightness of bearings of a back wheel
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Air central air
+ 16. Electric equipment


9.6.3. Bearing of a nave of a forward wheel

GENERAL INFORMATION

Rotary fist and bearings of a nave of a forward wheel

1–internal oil sealing ring;
2–internal bearing;
3–external ring of the internal bearing;
4–rotary fist;
5–brake board;
6–nave;
7–external oil sealing ring;
8–external bearing;
9–external ring of the external bearing;
10-rasporny plug.

Removal


Prevention

Needlessly do not remove a brake board.

Do not mix internal and external bearings of a nave.


PERFORMANCE ORDER
1. Remove a rotary fist.
2. The special AA0A adaptation ОК130 331 remove a nave.
3. Special A18 adaptations ОК130 175 and ОК130 175 А17 remove the external bearing, an external oil sealing ring and the rasporny plug from a nave.
4. Replace an oil sealing ring irrespective of its condition.
5. Disassemble a rotary fist.

Prevention

External rings of bearings remove gradually and carefully.


6. A screw-driver remove an internal oil sealing ring.
7. Remove the internal bearing.
8. Special adaptations ОК130 170 015 and a hammer remove an external ring of the internal bearing.

Prevention

Exclude falling of an external ring of the internal bearing at its removal.

Needlessly do not remove a brake board. Repeatedly do not establish earlier removed brake board.


9. Note the mutual provision of a brake board and a rotary fist.
10. A chisel remove a brake board from a rotary fist.

Check

Before survey wash up all details. Replace all damaged details. Insignificant traces of a rust remove with a fine-grained emery paper.

PERFORMANCE ORDER
1. Check the bearing on lack of wear, damages and jamming.

Prevention

Replace the bearing in collecting (internal and external rings).


2. Check a rotary fist on lack of cracks or damages, and also rusts and developments in installation sites of bearings.
3. Check a brake board on absence of damages.
4. Check a nave on lack of cracks or damages, and also rusts and developments in installation sites of bearings.

Assembly


Prevention

If replacement of bearings or a rotary fist was carried out, before assembly it is necessary to adjust a preliminary tightness of bearings.


PERFORMANCE ORDER
1. If the brake board acted in film, using the special adaptation, establish a new brake board.
2. Establish external rings of bearings in a rotary fist.
3. Put lithium greasing on the areas shown in drawing.
4. Establish against the stop the internal bearing in an opening of a rotary fist.
5. Grease a working edge of a new internal oil sealing ring.
6. Establish an internal oil sealing ring in an opening.
7. Establish earlier removed rasporny plug or the plug chosen in the course of preliminary adjustment of a tightness of bearings in an opening of a rotary fist.
8. Establish the external bearing in an opening of a rotary fist.
9. Grease a working edge of a new external oil sealing ring.
10. Establish a new external oil sealing ring in an opening.
11. Establish a rotary fist.
12. The special AA0A adaptation ОК130 331 establish a nave in a rotary fist.