KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
- 14. Body
   14.1. Inhaling moments
   14.2. Cowl
   14.3. Trunk lid
   14.4. Trunk lid hinge
   14.5. Door of a luggage compartment
   14.6. Gas-filled rack of support of a door of a luggage compartment
   14.7. Lock of a door of a luggage compartment
   14.8. External handle of a door of a luggage compartment
   14.9. Forward door
   14.10. Vlagozashchitnoye door consolidation
   14.11. Back door
   14.12. Dashboard
   14.13. Ceiling
   14.14. Lateral upholstery of a luggage carrier of five-door cars
   14.15. Back upholstery of a luggage carrier
   14.16. Top upholstery of a forward rack
   14.17. Bottom upholstery of the central rack
   14.18. Top upholstery of the central rack
   14.19. Upholstery of a back rack of four-door cars
   14.20. Upholstery of a back rack of five-door cars
   14.21. Upholstery of a forward door
   14.22. Overlay of a threshold of a forward door
   14.23. Upholstery of a back door
   14.24. Upholstery of a door of a luggage compartment
   14.25. Overlay of a threshold of a back door
   14.26. Back shelf
   14.27. Upholstery of an arch of a back wheel of four-door cars
   14.28. Upholstery of an arch of a back wheel of five-door cars
   14.29. Front bumper
   14.30. Rear bumper
   14.31. Forward seats
   14.32. Upholstery of a back of a forward seat
   14.33. Upholstery of a pillow of a forward seat
   14.34. Head restraint
   14.35. The leaning-back hinge of a forward seat
   14.36. Back sitting
   14.37. Seat belts
   14.38. Seat belts of a back seat
   14.39. Bracket of fastening of a back seat belt
   14.40. The distances designed on the plane, for check of distances between separate points of a body of the car
   14.41. The actual distances of check of distances between separate points of a body of the car
+ 15. Air central air
+ 16. Electric equipment


14.11. Back door

GENERAL INFORMATION

Back door

1–internal handle of opening of a door;
2–door upholstery;
3–pylevlagozashchitny film;
4–a directing sealant of glass;
5–directing glasses;
6–back glass;
7–sealant of back glass of a door;
8–glass;
9–window regulator;
10-external handle of opening of a door;
11-door lock;
12-limiter of opening of a door;
13-door hinge.

Removal

The door fastens to a car body two hinges and the limiter of opening of a door. The limiter of opening of a door limits size of opening of a door.

Hollow rubber consolidation of a door is established on a ledge of a door and prevents moisture and dust penetration between a door and a body.

The door lock is connected by drafts to external and internal handles of opening of a door.

The window regulator with an electric drive consists of the window regulator mechanism with the glass fixed on it, a lobby directing glasses, the switch established in an armrest and a plastic frame, protecting all components.

The shock plate of the lock of a door can be adjusted for reliable and soft closing of a door.

PERFORMANCE ORDER
1. Turn out one screw of fastening of an external vlagozashchitny strip of a door.
2. Remove an external vlagozashchitny strip of a door.
3. Remove a door upholstery.
4. Remove the internal handle of unlocking of the lock of a door in the following order:

      – disconnect from the handle two drafts;
      – remove the internal handle of a door.
5. Remove a pylevlagozashchitny film, gradually separating it from a door frame.
6. Remove directing sealant of glass.
7. Turn out one bolt and one screw of fastening central directing glasses.
8. Remove central directing glasses.
9. Remove back glass of a door.

10. Remove glass in the following order:

      – turn out two bolts of fastening of glass to a window regulator;
      – inclining and lifting a back part remove glass from the outer side of a door.

11. Through an opening in the internal panel of a door turn out two nuts of fastening of the external handle of a door.
12. Remove the external handle of a door.
13. Turn out three screws of fastening of the lock of a door.
14. Through an opening in the internal panel of a door remove the door lock.
15. Turn out six nuts of fastening of a window regulator.
16. Through an opening in the internal panel of a door remove a window regulator.
17. Through an opening from hinges extend a plait of wires from a door.
18. Remove an external molding of a fringing of glass.
19. Remove the limiter of opening of a door in the following order:

      – turn out a bolt of fastening of the limiter of opening of a door;
      – through an opening in the internal panel of a door remove the limiter of opening of a door.
20. Remove a door in the following order:

      – turn out bolts of fastening of both hinges;
      – remove a door from the car.

Installation

PERFORMANCE ORDER

1. Establish a door in the following order:

      – establish properly a door on the car;
      – screw bolts of fastening of both hinges.

Inhaling moment: 18–30 N • m

2. Establish the limiter of opening of a door in the following order:

      – through an opening in the internal panel of a door establish the limiter of opening of a door;
      – screw a bolt of fastening of the limiter of opening of a door.
3. Establish an external molding of a fringing of glass.
4. From hinges of a door pass at a door a plait of wires.
5. Establish a window regulator into place.
6. Screw six nuts of fastening of a window regulator.

Inhaling moment: 9–13 N • m

7. Put the door lock through an opening in the internal panel of a door.
8. Fix the door lock three screws.
9. Put to a door the external handle of a door.

10. Establish the external handle of a door in the following order:

      – connect drafts of the lock for the external handle of a door;
      – fix two nuts the external handle of a door.

11. Connect draft of the external handle of the lock of a door for the door lock.
12. Establish glass in the following order:

      – for greasing at installation of glass use soap solution;
      – insert outside of a door at first a forward part of glass, then, turning and lowering, establish glass at a door and arrange it on a window regulator arm.

Prevention

Be convinced that glass is correctly established in the directing.


13. Tighten two bolts of fastening of glass.

Inhaling moment: 2–3 N • m

14. If necessary, adjust the provision of glass.
15. Establish back glass at a door.
16. Establish central directing glasses.
17. Establish directing sealant of glass.
18. Establish on a door a pylevlagozashchitny film and deduce drafts of the internal handle of opening of the lock of a door from a pylevlagozashchitny film.
19. Establish the internal handle of a door in the following order:

      – connect to the handle two drafts of the lock of a door.
20. Establish a door upholstery.
21. Establish an external vlagozashchitny strip of a door.
22. Move glass up against the stop.