KIA RIO

since 2000 of release

Repair and car operation



Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
- 14. Body
   14.1. Inhaling moments
   14.2. Cowl
   14.3. Trunk lid
   14.4. Trunk lid hinge
   14.5. Door of a luggage compartment
   14.6. Gas-filled rack of support of a door of a luggage compartment
   14.7. Lock of a door of a luggage compartment
   14.8. External handle of a door of a luggage compartment
   14.9. Forward door
   14.10. Vlagozashchitnoye door consolidation
   14.11. Back door
   14.12. Dashboard
   14.13. Ceiling
   14.14. Lateral upholstery of a luggage carrier of five-door cars
   14.15. Back upholstery of a luggage carrier
   14.16. Top upholstery of a forward rack
   14.17. Bottom upholstery of the central rack
   14.18. Top upholstery of the central rack
   14.19. Upholstery of a back rack of four-door cars
   14.20. Upholstery of a back rack of five-door cars
   14.21. Upholstery of a forward door
   14.22. Overlay of a threshold of a forward door
   14.23. Upholstery of a back door
   14.24. Upholstery of a door of a luggage compartment
   14.25. Overlay of a threshold of a back door
   14.26. Back shelf
   14.27. Upholstery of an arch of a back wheel of four-door cars
   14.28. Upholstery of an arch of a back wheel of five-door cars
   14.29. Front bumper
   14.30. Rear bumper
   14.31. Forward seats
   14.32. Upholstery of a back of a forward seat
   14.33. Upholstery of a pillow of a forward seat
   14.34. Head restraint
   14.35. The leaning-back hinge of a forward seat
   14.36. Back sitting
   14.37. Seat belts
   14.38. Seat belts of a back seat
   14.39. Bracket of fastening of a back seat belt
   14.40. The distances designed on the plane, for check of distances between separate points of a body of the car
   14.41. The actual distances of check of distances between separate points of a body of the car
+ 15. Air central air
+ 16. Electric equipment


canadian rx


14.30. Rear bumper

GENERAL INFORMATION

Rear bumper

1–overlay of a bumper;
2–bolt of fastening of a bumper;
3–foamy absorber of energy;
4–amplifier of a bumper.

The rear bumper consists of three parts: overlays of a bumper, foamy absorber of energy and amplifier of a bumper.

The slip is made of polypropylene. The foamy absorber of energy is made of expanded polystyrene.

The amplifier of a bumper is made of metal. The foamy absorber of energy is located between an overlay of a bumper and the amplifier.

Removal

PERFORMANCE ORDER
1. Turn out three screws, fixing the left back mudguard to protection of an arch of a wheel.
2. Remove the right mudguard.
3. Turn out three screws, fixing the right back mudguard to protection of an arch of a wheel.
4. Turn out one screw of fastening of the right side of a bumper
5. Repeat operations on the left side of a bumper.
6. Turn out nuts on the left side in a luggage carrier.
7. Repeat operation on the right side.
8. Release eight clamps of fastening of the top part of a bumper.
9. Turn out two bolts of fastening from the left back support of a bumper.

10. Repeat operation on the right side.

11. Remove a rear bumper.

Installation

PERFORMANCE ORDER
Establish a rear bumper in sequence, return to removal.

Inhaling moment: 32–47 N • m

Check

PERFORMANCE ORDER
Check an overlay of a rear bumper on absence of damages and reliability of its fastening.