KIA RIO

since 2000 of release

Repair and car operation


Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
- 15. Air central air
   15.1. Specifications
   15.2. Contour of central air of air
   15.3. Remarks at replacement of elements of central air of air
   15.4. Connection of elements of central air of air
   15.5. Precautionary measures
   15.6. Verification of operational characteristics
   15.7. Diagnostics air central air with use of manometers
   15.8. Check of a gap of coupling of the compressor of the conditioner
   15.9. Check of coupling of the compressor of the conditioner
   15.10. Oil for greasing of the compressor of the conditioner
   15.11. Check of level and an oil dolivka in the conditioner compressor
   15.12. Air filter of the evaporator
   15.13. Sensor of double pressure
   15.14. Conditioner compressor
   15.15. Condenser check
   15.16. Check of the fan of the condenser
   15.17. Receiver \dryer check
   15.18. Check of the thermostatic sensor (termistor)
   15.19. Check of the engine of the fan
   15.20. Check of the block of resistors of the engine of the fan
   15.21. The switch of supply of air in car salon
   15.22. Control panel air central air
+ 16. Electric equipment

15.2. Contour of central air of air
GENERAL INFORMATION

Arrangement of elements of central air of air on the car

1–a soaking-up tube;
2–condenser fan;
3–tube;
4–sensor of double pressure; 		5–receiver / dryer;
6–colder pipe;
7–evaporator;
8–evaporator cover.

Elements of central air of air

1–a soaking-up tube;
2–discharge hose;
3–expansion hose;
4–condenser;
5–conditioner compressor;
6–a directing pulley;
7–belt of a drive of the compressor of the conditioner;
 8–arm of the compressor of the conditioner;
And – nuts, 18–23 N • m;
In – a bolt, 16–32 N • m;
With – a bolt, 24–36 N • m;
D–nut, 32–48 N • m;
Е–nut, 24–32 N • m.

Instruction on coolant application

 Liquid coolant R–134a with the high content of flying substances. Its hit on skin can end with frostbite therefore at work with a coolant it is necessary to dress protective gloves.

As standard measures of protection at work with a coolant it is necessary to use points for protection of eyes. At coolant hit on clothes or protective equipment, immediately wash out the struck place a large amount of water.

Liquid coolant R-134a is stored in containers (cylinders). Store a cylinder with a coolant at temperature no more 52°C.

For check of tightness of central air use the electronic sensor. Keep in mind that coolant R-134a after contact to a flame decays with allocation of very poisonous gas.

Use only the recommended oil for greasing of elements of central air of air, otherwise the system can fail.

PAG greasing intensively absorbs moisture from atmospheric air therefore it is necessary to observe the following precautions:

– at separation of components of central air of air, immediately close connections by the corresponding covers for an exception of hit of moisture in system;
– at installation of new components of central air of air remove from them protective covers directly ahead of their installation;
– connect tubes and hoses of central air of air as soon as possible to reduce hit in moisture system;
– use greasing for air central air only from the tight container.

If there was a casual discharge of central air of air, before service of system air a workplace.