KIA RIO

since 2000 of release

Repair and car operation

Rio KIA
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, A5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmission
+ 9. Axes and power shafts
+ 10. Suspension bracket
+ 11. Wheels and tires
+ 12. Steering
+ 13. Brake system
+ 14. Body
+ 15. Air central air
- 16. Electric equipment
   16.1. Specifications
   16.2. Electric chains
   + 16.3. Generator
   + 16.4. Storage battery
   16.5. Starter
   16.6. Check at a provorachivaniye of a cranked shaft not the heated-up engine
   16.7. Check of an electric chain of the traction relay
   16.8. Check of the traction relay
   16.9. Check of brushes and shchetkoderzhatel
   16.10. Check of coils of a stator
   16.11. Rotor check
   16.12. Removal and starter installation
   16.13. Starter repair
   16.14. Multipurpose switch
   16.15. Sound signal
   16.16. The block of safety locks and the relay, established in car salon
   16.17. Check of the relay of the activator of the lock of a door
   16.18. Check of the switch of adjustment of provision of an external rear-view mirror
   16.19. Check of the activator of provision of an external rear-view mirror
   16.20. Check of the engine of a window regulator
   16.21. Check of a heater of back glass
   16.22. Repair of a current-carrying strip of a heater
   16.23. Engine of a screen wiper of a windscreen
   16.24. Stekloomyvateli
   16.25. Adjustment of light of headlights
   16.26. Adjustment of light of fog lights
   16.27. Safety cushions (SRS)
   16.28. Precautionary labels
   16.29. Safety cushion of the driver and spiral wire
   16.30. Safety cushion check
   16.31. Check of a spiral wire (spring)
   16.32. Safety cushion of the forward passenger
   + 16.33. Electric circuits

16.32. Safety cushion of the forward passenger

GENERAL INFORMATION

Prevention

Do not assort and do not repair elements of system of a safety cushion.

If the safety cushion fell or on it water, lubricants or oil, and also if there are cracks, dents or other defects in the case or the socket got, replace a safety cushion.

The removed safety cushion is necessary for storing in a pure dry place, the face up. Have no on a safety cushion extraneous subjects which safety cushions at expansion can put serious traumas.

Do not subject a safety cushion to influence of temperature above 93 °C.

Do not try to measure resistance of an electric chain of a pyrotechnic gas generator of a safety cushion, as probably unauthorized expansion of a safety cushion of the driver.

After operation of a safety cushion it is necessary to replace it together with a wire which underwent influence of gases of a pyrotechnic gas generator.

PERFORMANCE ORDER

	1. Disconnect a wire from the negative plug of the storage battery.
Prevention Before service of system of safety cushions be convinced that passed not less than 30 with the ambassador of switching off of ignition and a wire detachment from the negative plug of the storage battery.
2. Remove a ware box.
3. Disconnect the electric socket of a safety cushion.
4. Remove safety cushions.

Diagnostics of malfunctions of system of a charging and methods of their elimination

Step	Check				Elimination method
1	Check the storage battery Tension: about 12,4 In			Yes	Look the following step
1	Check the storage battery Tension: about 12,4 In			No	Check the storage battery
2	Start up the engine and check, whether the control lamp of a charging of the storage battery burns			Yes	Look a step 4
2				No	Look the following step
3	Check, whether the correct tension on generator plugs			Yes	Check a condition of the wire connecting the storage battery and contact In the generator
	Contact	Ignition is included by ON, In	Tension, In	No	Check a condition of wires Replace the generator
	B	About 12	14,1–14,7
	L	About 1	14,1–14,7
	S	About 12	14,1–14,7
4	1. Turn on the ampermeter (with a measurement limit at least 80А) between the plug B and the plug In wires 2. Start up the engine 3. Switch off everything electric consumers and press a brake pedal 4. Check that the device shows a current 65 And or more at frequency of rotation of 2500-3000 ^mines-1 Prevention Do not connect to "weight" contact In			Yes	Charging system as it should be
4				No	Look the following step
5	Be convinced that a tension of a belt of a drive of the generator as it should be			Yes	Replace the generator
5				No	Adjust a tension of a belt of a drive of the generator

Diagnostics of malfunctions of system of start-up and methods of their elimination

001 Starter does not turn a cranked shaft of the engine

Step	Check		Elimination method
1	Check, whether the cranked shaft of the engine is turned at completely charged storage battery	Yes	Check charging system
		No	Look the following step
2	Check, whether tension on the plug B of the traction relay moves	Yes	Look the following step
		No	Check a condition of wires
3	Check, whether tension of the storage battery to contact of S of the traction relay moves at the pressed pedal of coupling (on cars with a mechanical transmission) or at installation of the lever of the selector in Park position (on cars with an automatic transmission) and key turn in the ignition lock in the situation START	Yes	Replace a starter
		No	Check the switch of blocking of a starter of provision of a pedal of coupling (on cars with a mechanical transmission) Check the switch of a range of transfers (on cars with an automatic transmission) Check the ignition lock Check a condition of wires

002 Engine of a starter quickly rotates

Step	Check		Elimination method
1	Check, whether the gear wheel of the obgonny coupling will mix up at starter inclusion (At inclusion of a starter click) should be audible	Yes	Remove a starter and check a condition of teeths on the obgonny coupling and a gear wreath of a flywheel
		No	Replace a starter

4 Cranked shaft of the engine rotates slowly

Step	Check		Elimination method
1	Check speed of rotation of a cranked shaft at completely charged storage battery	Yes	Believe charging system
		No	Look the following step
2	Check reliability of fastening of wires of a starter and absence of corrosion on them	Yes	Repair or replace wires
		No	Check absence of jamming of the engine of a starter. Repair or replace a starter

11 Control lamp of a charging burns at the working engine

Step	Check		Elimination method
1	Check tension of the storage battery on frequency of rotation of idling Tension 14,1-14,7B	Yes	Check a condition of the wires connecting the storage battery and contact of the L generator, the generator and a control lamp
		No	Believe charging system

004 Discharged storage battery

Step	Check		Elimination method
1	Believe charging system	Yes	Include ignition and check current size Current: less than 20 мА
		No	If necessary, replace or repair details